By Nick Gromicko and Rob London

   

Electrical panels are boxes that house circuit breakers, which are safety devices that stop the electrical current if it exceeds the safe level for some portion of the home electrical system.

 

 

 

Safety

 
Many people, even experienced electricians, have been killed or seriously injured while opening electrical panels. In 1991, an Atlanta electrician was killed while attempting to inspect a panel that had a faulty spring-loaded bus-bar assembly. Apparently, the bus-bar was moved while the electrician was opening the panel, causing an arc and a lethal electrical explosion. Generally, two factors contribute to these situations:  defective components and complacency.

Inspectors must be aware that all forms of electrical inspections, especially electrical panel inspections, are inherently dangerous. Practice calm, steady movements and learn to avoid distractions. A sudden flash, shout or movement could cause an inspector to lunge and touch an electrically live and dangerous component. Advise your client that they should never remove an electrical panel cover themselves, as they should leave this duty to InterNACHI inspectors or qualified electricians. Before touching the electrical panel, inspectors should ask themselves the following questions:

 

• Do I have an escape path? Make sure that you know where you can safely turn or step if you must safely escape a dangerous surprise, such as bees or sparks. An unfortunately placed shovel or extension cord, for instance, can turn a quick jerk into a dangerous fall.
• Are the floors wet? Never touch any electrical equipment while standing on a wet surface!
• Does the panel appear to be wet? Check overhead for dripping water that has condensed on a cold water pipe. Moisture can arrive in more ways than you can imagine.
• Is the panel rusty? Rust is an indication of previous wet conditions that may still exist.

 

As an optional safety measure, use a voltage ticker to make sure the box is safe to touch. If the alarm sounds on the device, have the box examined by a qualified electrician.

 

While removing the panel, inspectors should:

 

• Stand a little back while removing the cover, which makes it easier to remain in a blocking position.
• Stand so as to block your client from touching the panel and its components.
• inform the client that opening the panel is a dangerous step, and that if sparks fly, the client should not touch the inspector.

 

 

Service Panel Inspection:

 

Inspectors can check for the following defective conditions during an electrical panel inspection:

 

• insufficient clearance. According to the 2008 National Electrical Code, most residential electrical panels require at least a 3-foot clearance or working space in front, 30 inches on either side, and a minimum headroom clearance of 6 feet, or the height of the equipment, whichever is greater. If obstacles would make it unsafe for you to inspect the service panel, you have the right to disclaim it.
• sharp-tipped panel box screws. Panel box cover screws must have blunt ends so they do not pierce the wires inside the box. Also, look for wires that pass too closely to the screw openings inside the electrical panel.
• circuit breakers that are not properly sized. Circuit breakers should not be too large or too small for the wires they serve.
• oxidation or corrosion to any of the parts. Oxidized or corroded wires will increase the resistance of conductors and create the potential for arcing. 
• evidence of electrical failures, such as burned or overheated components.
• evidence of water entry inside the electrical panel. Moisture can corrode circuit breakers so that they won't trip, make connections less reliable, and make the equipment unsafe to touch.
• evidence of missing or improper bonding.  This may indicate improper wiring, damaged equipment or unsafe conditions.
• panel manufactured by Zinsco. These panels do not offer as much over-current and fire protection provided by most other electrical panels. Zinsco panels often have damaged bus bars that can cause overheating of the circuit breaker, failure of the circuit breaker to trip and, ultimately, a fire in the structure. Many experts advise that Zinsco panels be replaced. Zinsco panels can generally be identified by a blue and silver "Zinsco" label inside the panel, and an embossed "Magnetrip" label at the top of the panel face.

 

In summary, electrical panels are potentially dangerous and should be inspected with care.